+49 (0)2233 - 611 500
sales@teqsas.de
Deutsch (German)
English
TEQSAS Logo

cyberTEQ – m is a distribution system for nearly all kinds of signals used in professional event technology.

The system consists of a mainframe and several converter modules. cyberTEQ – m uses the IEEE 802.3 Gigabit-Ethernet as backbone. Using converter modules in addition to the mainframe enables the link between Ethernet and other event technology signals. By using only one connection between two cyberTEQ – m – mainframes the following data can be transmitted simultaneously:
  • Audio (Dante™, EtherSound®, CobraNet®, MyMix®, Roland Digital Snake®)
  • Light (MA-Net, ART Net)
  • Ethernet (z.B. L-Acoustics LA Network Manager, Yamaha CL Editor, Sennheiser Wireless System Manager, Shure Wireless Workbench,…)
  • AES3 digital outputs
  • DMX 512 / ART-Net
  • MIDI
  • RS-232 / RS-422 / RS-485
  • Analog Intercom
  • WLAN (e.g. to use an iPad® for remote control)
Rückseite cyberTEQ – mf²c² -mainframe

Rear panel of cyberTEQ – mf²c² -mainframe

cyberTEQ – m can do even more. It is not only a point to point system, it’s much rather a multipoint to multipoint: Connecting a third, a fourth, a fifth … cyberTEQ – m the signals are splitted and are available at all locations. It makes no difference if you build a ring, a star or a mix of ring and star: The network builds its topology by itself. (The network topology is built by itself, but by using EtherSound® for example it might be necessary to build VLans to realise daisy chain).
By programming cyberTEQ – m mainframe you can assign which signal is available at which position. Programming can be done by webbrowser or serial-port with Windows® based PCs or MACs®. To reach redundancy cyberTEQ – m can be connected in a ring or in a double star etc: The show goes on even if one cable is broken.
Rear panel of cyberTEQ – mf²c² -mainframe, port 19 and 20 are used for additional uplinks exclusively at this model.

cyberTEQ – m-mainframe has up to four specific ports for long distance connections.

These ports are realised with either copper or optical fibre connectors and are placed on the front panel as well as on the rear panel. For this reason cyberTEQ – m mainframe is available in four different versions:
  • mc²-mainframe two copper ports on the front panel*
  • mfc-mainframe one copper port and one fibre port on the front panel*
  •  mf²-mainframe two fibre ports on the front panel*
  • mf²c²-mainframe two fibre ports on front and two copper ports on rear panel*
mc² Uplink Vorderseite

mc² Uplink in the front

mfc Uplink Vorderseite

mfc Uplink in the front

mf² and mf²c² Uplink Vorderseite

mf² und mf²c²
Uplink in the front

At cyberTEQ – mf²c²-mainframe each optical fibre port on the front is assigned to one copper port on the rear, so if one optical connection is established its coupled copper port is switched off automatically. This gives the advantage of a high flexibility, because you can choose the connection without having to adapt the internal programming.
The maximum length of a copper connection using a CAT cable is limited to 80 m. Using the optical fibre connection the maximum length is safe up to 550 m. On request we offer single mode converters and cables: In this case the maximum length is 10 km.
In addition to the long distance ports, you will find four Ethernet RJ45 Gigatbit/s ports on the front and ten Ethernet RJ45 Gigatbit/s ports on the rear to connect directly your equipment with Ethernet connections. In addition there are two slots on the front to equip cyberTEQ – m-mainframe with converter modules, which offer transmission of different signals (see below). Within a few minutes you can easily change the configuration of cyberTEQ – m by removing or inserting different modules. If you order cyberTEQ – m without optional modules the slots are covered with blank panels. cyberTEQ – m latency is less than 10 μs and reaches values below 3 μs depending on programming. It creates nearly no jitter (three times less compared to most Ethernet switches). cyberTEQ – m is built in a roadworthy 19”, 1 RU housing, depth 390 mm, weight 6.2 kg. The mainframe contains an internal PSU connected by Neutrik® PowerCon and runs on 100-240V~ / 50-60Hz. An optional external cyberTEQ – psu in a 19“ / 1 RU housing is available. This improves system stability and offers to run the system at two power lines.
 All connectors for signal transmission are heavy duty Neutrik® connectors with locking mechanism, designed for stringent demands on the road. The optical connector is the LC-compatible Neutrik® OpticalCon.

 cyberTEQ – m can be equipped with the following modules:

Dante™ to 4 x AES3 out – module

Dante™ to 4 x AES3 out – module
InterCOM – module

InterCOM – module
dual RJ45 & USB power – module

dual RJ45 & USB power – module
dual RJ45 – module

dual RJ45 – module
dual band WLAN – module

dual band WLAN – module
DMX-512 / Artnet – module

DMX-512 / Artnet – module
fibre – module

fibre – module
SERIAL – module

SERIAL – module
Menu